€0,00
Add to cart

17er Nakiri Historische Werkstoffe

17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
17er Nakiri Historische Werkstoffe
€0,00
* Incl. tax Excl. Shipping costs

Ein 17er Nakiri mit einer Schneide aus 1.2562, Seitenlagen aus historischem Eisen und einem Griff aus historischem Eichenholz. Read more..

With this knife you hold a real piece of history in your hands. At the same time, there is a bridge between historical materials and craft techniques and modern high-end materials. The side layers of this blade are made of four different steels from different centuries that have been forged and refined with one another. Iron from a wall anchor from 1450, iron from a wall anchor from 1653, iron from the year number of a church from 1735 and iron from support struts from 1848 were used. The cutting edge of the blade is made of high-performance steel 1.2562. The handle is made of oak from the roof of a church from 1300.

The nakiri is considered a classic Japanese vegetables knife, although it is of course also suitable for cutting meat and fish. Due to the high height of the blade, it is easy to let it run along the fingers. The cutting edge is only slightly curved along its entire length, which makes it ideal for push and pull cuts.

The blade is thinly ground, the geometry is between that of a laser and a user-friendly.

After the last fire weld at 970 degrees, the initial package with a thickness of approx. 55mm was forged down to approx. 20mm within one heat with a forging start temperature of 900 degrees and then immediately cooled to below 720 degrees. This was followed by forging the blank at a maximum of 780 degrees. After each heat, the blank was cooled to below 720 degrees. This process produces a very fine-grained matrix as well as very small and finely divided carbides.

I have the drawer lid boxes made for me by a master carpenter friend. This box is made of walnut and has the manufacturer's branding stamp on the underside. The blade rests on a wooden block, in which magnets are concealed and which is covered with a thin layer of balsa wood. This will prevent the blade from scratching. I would like to point out that I do not recommend using the caskets as the only transport lock. The blade is held well by the magnets, but it can slip if it is hit or jarred. If necessary, you can simply pad the box with a kitchen towel or something similar.

For buyers from non-EU countries: Due to the larger dimensions of the sliding lid box, the shipping is more expensive than usual.

Schneidenlänge/lenght of edge:

170mm

Max. Klingenhöhe/max. height of the blade:

60mm

Klingenstärke am Rücken/thickness of the blade:

 
Angel/tang:

3,4mm

Kehl/choil:

3,0mm

Mitte/middle:

2,0mm

An der Spitze/at the tip:

1,5mm

Grifflänge/lenght of the handle:

123mm

Gewicht/weight:

193g

Schwerpunkt/balancepoint:

38mm vor dem Griff/before the handle

Geometrie/geometry:

Zwischen Laser und Userfriendly/between laser and user-friendly

Schneidenstahl/core steel:

1.2562, C=1,45%, W= 3,0%, Cr= 0,3%, V= 0,2%, ca. 65hrc

Zwischenlage/intermediate layer:

Reinnickel/nickel

Seitenlagen/clad:

Eisen von/iron from: 1450, 1653, 1735 und 1848

Griffmaterial/material of the handle:

Eichenholz von 1300/oak wood from 1300

Griffform/ shape of the handle:  Hakkaku (achteckig/octagonal)

Box

 Nussbaum/Walnut

 

Please accept cookies to help us improve this website Is this OK? Yes No More on cookies »